低周反复荷载下Q460钢材框架柱抗震性能分析     

刘宽  马煜东  黄娇  刘笑笑  苏佶智 《震灾防御技术》2019,14(3):535-554

为了进一步完善Q460钢材在抗震设计规范中相关限值的要求，本文利用有限元软件ABAQUS，以轴压比、翼缘宽厚比、腹板高厚比和壁板宽厚比为变量，建立了共48根“工”字型框架柱和“箱”型框架柱，分析了其抗震性能。结果表明:翼缘宽厚比对框架柱的能量耗散系数影响较小；能量耗散系数随轴压比、腹板高厚比（“工”字型）和壁板宽厚比（“箱”型）增大而明显减小；框架柱的极限承载力随轴压比的减小及壁板宽厚比和翼缘宽厚比的增大而逐渐增大，当腹板高厚比接近规范限值时，承载力下降趋势明显增大。与采用Q235钢材的框架柱相比，Q460钢材框架柱的延性较小，仅为2左右；当采用Q460钢材时，“工”字型框架柱的极限位移角限值建议取为0.03，“箱”型框架柱的极限位移角限值建议取为0.032。规范中对翼缘宽厚比限值的规定偏于保守，其值最大可取至9。无论是“工”字型框架柱还是“箱”型框架柱，其腹板高厚比均不宜过大。Q460钢材框架柱的刚度退化率随轴压比的增大而增强，且翼缘宽厚比越大，腹板高厚比越小，柱的初始刚度越大，刚度退化程度越明显。  相似文献   

Concurrent Determination of U‐Pb Age and REE Mass Fractions of Zircon by High Mass Resolution SIMS     

Yu Liu  Qiu‐Li Li  Guo‐Qiang Tang  Xian‐Hua Li 《Geostandards and Geoanalytical Research》2020,44(3):421-437

A combined geochronological and geochemical investigation for the same domain of zircon provides valuable information on timing and genesis, particularly in the case of multi‐growth metamorphic zircon. A high spatial resolution concurrent analytical method for zircon U‐Pb age and rare earth element content was successfully achieved in this study, using a multi‐collector secondary ion mass spectrometer (SIMS) at a ~ 8 μm diameter scale. Special instrument parameters were employed, including a high mass resolution of approximately 15000 applied to replace the previous energy filter method, and a dynamic multi‐collector mode used to reduce the measurement time to 18 min per analysis. Six zircon reference materials yielded precise and accurate ²⁰⁶Pb/²³⁸U ages, which are comparable to those obtained by the ordinary mono‐collector method, but with 2–3 times higher spatial resolution. All zircon grains measured in this study showed enriched heavy‐REE (HREE) contents consistent with previously reported values determined by LA and solution ICP‐MS methods. The light‐REE (LREE) mass fractions measured using both SIMS and LA‐ICP‐MS methods in this study, although with quite different volume, show consistent results within uncertainties.  相似文献   

High‐Precision,High‐Accuracy Oxygen Isotope Measurements of Zircon Reference Materials with the SHRIMP‐SI     

Janaína N. vila  Trevor R. Ireland  Peter Holden  Peter Lanc  Andrew Latimore  Norm Schram  John Foster  Ian S. Williams  Liane Loiselle  Bin Fu 《Geostandards and Geoanalytical Research》2020,44(1):85-102

Analytical protocols for SHRIMP‐SI oxygen isotope analysis (δ¹⁸O) of a suite of zircon reference materials (RMs) are presented. Data reduction involved a robust estimate of uncertainties associated with the individual spot as well as for groups where the spot data are combined. The repeatability of δ¹⁸O measurements is dependent on both the analytical conditions and the choice of the primary reference material. Under optimised conditions, repeatability was often better than 0.4‰ (2s) allowing sample uncertainties to be obtained to better than 0.2‰ (at 95% confidence limit). Single spot uncertainty combined the within‐spot precision with the scatter associated with repeated measurements of the primary zircon reference material during a measurement session. The uncertainty for individual spots measured under optimised conditions was between 0.3 and 0.4‰ (at 95% confidence). The analytical protocols described were used to assess a variety of zircon RMs that have been used for geochronology and for which laser fluorination oxygen isotope data are available (Temora 2, FC1, R33, QGNG and Ple?ovice), as well as zircons that have been used as RMs for trace element or other types of determination (Mud Tank, Monastery, 91500, AS57, AS3, KIM‐5, OG1, SL13, CZ3 and several other Sri Lankan zircons). Repeated analyses over nine sessions and seven different mounts show agreement within analytical uncertainty for Temora 2, FC1, R33, QGNG, Ple?ovice and 91500, when normalised to Mud Tank. For existing ion microprobe mounts with these materials, an appropriate δ¹⁸O can be determined. However, care should be taken when using zircons from the Duluth Complex (i.e., FC1, AS57 and AS3) as reference materials as our data indicated an excess scatter on δ¹⁸O values associated with low‐U zircon grains.  相似文献   

建筑物侧面轮廓线约束的高分辨率遥感影像建筑物高度估算方法     

陈辉  张卡  宿东  王蓬勃 《测绘通报》2019,(9):34-37,72

针对现有利用阴影长度法提取建筑物高度时存在的阴影间相互遮挡问题，提出了一种基于建筑物侧面轮廓线进行建筑物高度估算的新方法。首先，利用RPC模型计算建筑物像点位移的方向与卫星成像角度，再将遥感影像进行旋转，使建筑物像点位移沿水平方向；然后，利用Canny算法进行轮廓检测，并构建一定长度的矩形形态学结构元素，对轮廓图像进行形态学开运算，以提取侧面轮廓线，再利用Hough变换与建筑物角点约束，对所提取的轮廓线进一步筛选；最后，根据卫星侧视成像时建筑物高度与像点位移的几何关系进行建筑物的高度估算。利用实际的高分辨率卫星影像对本文方法进行了验证，并与阴影法估算建筑物高度进行了对比。试验结果证明，利用建筑物侧面轮廓线进行建筑物高度估算平均误差可以达到0.7 m，且实际精度优于使用阴影法进行建筑物高度估算。  相似文献   

机载激光点云中高压电塔自动识别方法   总被引：2，自引：2，他引：0  

刘洋  杨必胜  梁福逊 《测绘通报》2019,(1):34-38

提出了一种基于格网特征的机载激光点云高压电塔自动识别方法。首先对机载激光点云数据进行滤波去噪处理；然后对点云数据进行规则格网化特征分析获得高压电塔粗识别区域；最后对粗识别区域进行外接邻域网格线性特征悬空点集检测以确定电塔识别结果，并以分层切片法分析获取电塔平面中心坐标。采用大型无人机实际线路巡检获取的机载点云数据对本文算法进行验证，试验结果表明本算法可实现高压电塔的快速自动识别，对无人机电力巡检智能诊断具有一定的促进作用。  相似文献   

Access routes to high mountain huts facing climate-induced environmental changes and adaptive strategies in the Western Alps since the 1990s     

Jacques Mourey  Ludovic Ravanel  Christophe Lambiel  Joël Strecker  Mattia Piccardi 《Norsk geografisk tidsskrift. Norwegian journal of geography》2019,73(4):215-228

ABSTRACT

In the European Alps, high mountain environments are subject to major impacts resulting from climate change, which strongly affect human activities such as mountaineering. The purpose of the study was to examine changes in access routes to 30 high mountain huts in the Western Alps since the 1990s. Data were derived from the use of two different methods, geo-historical studies and a questionnaire, and were used to identify both the climate-related processes affecting the climbing routes and the strategies implemented by public entities, Alpine clubs, guide companies, and hut keepers to maintain acceptable safety and technical conditions. The case studies revealed issues affecting three access routes and the results from the questionnaire showed that the main processes affecting access routes were loss of ice thickness and retreat from the front of the glaciated areas. Commonly, in situ equipment was installed to facilitate access for mountaineers and/or a part of a route was relocated to a safer area. The authors conclude that in most cases, the measures were effective but they were limited by financial, ethical and legal issues, especially in protected or classified areas that could jeopardise their durability and effectiveness.  相似文献   

Revisiting the morphological method in two-dimensions to quantify bed-material transport in braided rivers     

Gilles Antoniazza  Maarten Bakker  Stuart N. Lane 《地球表面变化过程与地形》2019,44(11):2251-2267

Research in the 1990s showed that bed-material transport rates could be estimated at the reach scale in both one-dimension and, over small spatial scales (10s of m), in two-dimensions. The limit on the latter was the spatial scale over which it was possible to obtain distributed data on morphological change. Here, we revisit the morphological method given progress in both topographical data acquisition and hydraulic modelling. The bed-material transport needed to conserve mass is calculated in both one and two dimensions for a 1600 m × 300 m Alpine braided river “laboratory”. High-resolution topographical data were acquired by laser scanning to quantify Digital Elevation Models (DEMs), and morphological changes caused by the flushing of the water intake were derived from repeated surveys. Based on DEMs of differences, 1D bed-material transport rates were calculated using the morphological method. Then, a 2D hydraulic model was combined with a topographic correction to route sediment through the network of braided channels and to obtain a spatially variable estimate of transport in both downstream and cross-stream directions. Monte Carlo simulation was applied to the routing model parameters, allowing identification of the most probable parameter values needed to minimize negative transport. The results show that within-section spatial compensation of erosion and deposition using the 1D treatment leads to substantial local errors in transport rate estimates, to a degree related to braiding intensity. Even though the 2D application showed that a large proportion of the total transport was actually concentrated into one main channel during the studied low flow event, the proportion of transport in secondary anabranches is substantial when the river starts braiding. Investigations of the effects of DEM resolution, competent flow duration and survey frequency related to ‘travelling bedload’ and sequential erosion-deposition emphasized the critical importance of careful data collection in the application of the morphological method. © 2019 John Wiley & Sons, Ltd.  相似文献   

准噶尔盆地玛湖凹陷西斜坡三叠系百口泉组扇三角洲优质储集层预测          下载免费PDF全文

桑林翔  刘军  王贵文  王苏天  李全  张云龙 《古地理学报》2020,22(6):1053-1064

针对准噶尔盆地玛湖凹陷西斜坡风南地区三叠系百口泉组扇三角洲砂岩物性空间变化大、优质储集层(孔隙度大于7.4%,渗透率大于0.05×10^-3μm²)预测难的问题,在沉积岩石学、地震沉积学以及地震反演和解释理论指导下,综合利用测井、岩心和三维地震等资料开展了高精度层序地层划分、沉积微相描述和优质储集层地震反演研究。建立了风南井区四级层序地层格架,明确了扇三角洲多期水进水退的充填过程,指出SSQ3和SSQ5是优质储集层的发育层系;识别出扇三角洲平原分流河道、河道间和扇三角洲前缘水下分流水道、河口坝、席状砂等沉积微相,指出扇三角洲平原是优质储集层发育相带;通过应用高分辨层序地层纵向边界和沉积相横向边界约束,进行分层相控叠后地震波阻抗反演,提升储集层预测精度,在SSQ3和SSQ5预测5个优质储集层发育区,提出3口井的井位建议,钻探均获工业油流。  相似文献   

川藏铁路交通廊道地质调查工程主要进展与成果     

郭长宝  王保弟  刘建康  涂杰楠  张永双  马剑飞  铁永波  韩冰  马鑫  刘峰  李雪  孟文  钟宁  杨志华  吴瑞安 《中国地质调查》2020,7(6):1-12

川藏铁路是我国正在规划建设的重点工程,由于其位于地形地貌和地质构造都极为复杂的青藏高原东部,在铁路规划建设中面临一系列迫切需要解决的关键地质问题: 区域性活动断裂与断错影响、地质灾害、高地应力及其引起的岩爆和大变形、高温热害、断裂带高压水与涌水突泥、高陡边坡稳定性等。为满足技术支撑川藏铁路规划建设、精准服务国家重大战略实施的需要,中国地质调查局部署了“川藏铁路交通廊道地质调查工程”,聚焦制约川藏铁路规划建设的关键问题,充分发挥地质调查工作对国家重大工程规划建设的支撑作用。2019年主要完成铁路沿线1:5万区域地质调查1 350 km²、1:5万地质灾害调查5 000 km²,建设6口大地热流地质参数井、8个地温监测站,完成地应力测量20孔,编制完成11份地质调查专报,提出的大渡河大桥段、理塘车站段、毛垭坝盆地段等线路优化建议/防灾建议被采纳; 首次将1:5 000大比例尺航空物探技术引入复杂山地铁路工程勘察,创新形成千米级超长水平钻孔定向取心钻进技术,实现500 m深的水平孔地应力测量突破等。该工程通过2019年调查研究,全力提升了铁路沿线地质调查程度与精度,并创新了复杂艰险山区重大工程地质问题与探测技术、地质灾害风险防控理论与减灾关键技术,有效支撑服务了川藏铁路规划建设。  相似文献   

福建北部近岸东台山岛火山岩形成时代、地球化学与古太平洋板块俯冲的响应          下载免费PDF全文

王飞飞  张勇  韩宗珠  宋维宇  吴浩  宁泽 《中国地质》2020,47(5):1426-1437

福建北部沿岸岛屿岩石组合以晚中生代火成岩为主，研究认为是古太平洋俯冲消减的产物，对反演洋盆构造演化具有重要的指示意义。本次对其中的福建北部海域东台山岛上广泛发育的酸性火山岩进行了锆石U-Pb定年以及全岩主微量地球化学分析工作。2件年代学样品分别获得了92 Ma和86 Ma的锆石U-Pb年龄，确定东台山岛火山岩形成于晚白垩世。全岩地球化学特征指示火山岩样品以酸性钙碱性岩石为主，整体富集Rb、Ba等元素，亏损Nb、Ta、Sr、Eu等元素，显示弧型岩浆岩的地球化学组成。研究认为东台山岛火山岩起源于古老下地壳变沉积岩熔融，并在浅层岩浆房内经历了不同程度的结晶分异过程。结合区域上晚中生代岩浆作用由陆向海的时空迁移特征，福建北部沿岸岛屿火山岩形成的深部动力学机制应该与古太平洋俯冲过程中的板片回转过程相关。  相似文献